General control of 100 meters of the controller is relatively little large, used in car decoration control is not very beautiful, if it is used in the engineering OK, eight function controller: water, a gradual, steady, flash, flash , slow flash, etc., the rainbow (lights) color works best with controllers. LED round second controller connection: rainbow plug two power cords, one of which is a common line, 100 meters behind the controller has four connections, one of which is the common thread of different colors controllers, lamp with plug common line with the controller will be able to highlight the common line are connected together, the other can take a few lines to connect the line, if not bright, it is not looking for a common line. LED flat three-wire, LED flat four-wire, I do not say, as long as it can control the flat four-wire can be controlled LED round wire, flat three-wire, flat four-wire, three specifications, we called him: 203 Controller , 1800W, 204 controller: can control a round wire, flat three-wire, flat four-wire, flat five lines, 2000W. Connection with the above methods, like I said, I tell you how to find the main controller with round wire, flat three-wire, flat four-wire, flat five-wire plug common line: Controller: color different from other power cord Flanagan line, only two to round wire, positive and negative points level, flat four-wire cable is probably the red or black wire, flat three lines: middle Flanagan, flat five lines: the middle of the Okanagan, so say something even more clear, the plug You can try your own common line interpolation, all positive and negative points level. There is so much simple good point. Then tell what size you controller: flat four-wire control 20 m 12V: 7.5 * 7.5 * 8CM 203/204: control round wire, flat three-wire, flat four-wire, flat five lines 100 meters 220V: 15 * 10.5 * 2CM
120V led rope light Description With
1. LED rope light roll, do not light up the rainbow.
2. Only in the light illuminated body scissors mark printed on the cut, otherwise it will cause a unit does not shine.
3. When installed, remove the lamp with a bent to one side, exposing 2-3MM copper, and cut it off with pliers, leaving no burrs, to avoid a short circuit.
4. Do not pass the installation or assembly process of the lamp with power supply, only access, the installation is good and under the right circumstances to power,
5. Installation under cold temperatures LED rope light, a few minutes can be energized, the lamp body becomes soft, easy to bend, and then power installation.
6. Installation and use, do not beat the lamp with a heavy object, and throw strike vibration.
7. Lamp end of the trap must be used before the end of the plug with glue cement.
8. Only the same size, the same voltage to two tubes connected with each other, the series total length must not exceed the maximum license length
9. Each interface must be solid, no short circuit risks, outdoor installation, each interface must use glass, plastic or other appropriate means sealing interface, ensure that all water interface.
10. Not be installed in the water, flammable, explosive environment, we must ensure the environment is well ventilated.
11. Fixed, do not use tight tie wire and other metal materials lamp, in order to avoid wire into the inner tube, resulting in short burning lamps.
12. Supply voltage should be marked with a lamp to, and install the appropriate fuse.
13. Lamp during use, do not use any object wrap, cover lamps.
14. Lamp Lamp body was found damaged, please immediately cut this part, can not continue to use, in order to avoid danger.
Fifteen. For flashing, water and other effects, use LED controller.
16. If unknown place, please contact the factory.
https://www.tumblr.com/blog/smd5050
120V led rope light Description With
1. LED rope light roll, do not light up the rainbow.
2. Only in the light illuminated body scissors mark printed on the cut, otherwise it will cause a unit does not shine.
3. When installed, remove the lamp with a bent to one side, exposing 2-3MM copper, and cut it off with pliers, leaving no burrs, to avoid a short circuit.
4. Do not pass the installation or assembly process of the lamp with power supply, only access, the installation is good and under the right circumstances to power,
5. Installation under cold temperatures LED rope light, a few minutes can be energized, the lamp body becomes soft, easy to bend, and then power installation.
6. Installation and use, do not beat the lamp with a heavy object, and throw strike vibration.
7. Lamp end of the trap must be used before the end of the plug with glue cement.
8. Only the same size, the same voltage to two tubes connected with each other, the series total length must not exceed the maximum license length
9. Each interface must be solid, no short circuit risks, outdoor installation, each interface must use glass, plastic or other appropriate means sealing interface, ensure that all water interface.
10. Not be installed in the water, flammable, explosive environment, we must ensure the environment is well ventilated.
11. Fixed, do not use tight tie wire and other metal materials lamp, in order to avoid wire into the inner tube, resulting in short burning lamps.
12. Supply voltage should be marked with a lamp to, and install the appropriate fuse.
13. Lamp during use, do not use any object wrap, cover lamps.
14. Lamp Lamp body was found damaged, please immediately cut this part, can not continue to use, in order to avoid danger.
Fifteen. For flashing, water and other effects, use LED controller.
16. If unknown place, please contact the factory.
https://www.tumblr.com/blog/smd5050
No comments:
Post a Comment